The almost unbelievable galley

[ad name=”intheboatshed-post”]

galley01-470

Galley drawing from On the High Seas – click for a larger image

Idly reading my first edition copy of On the High Seas by E Keble Chatterton, I was astonished to find this drawing of a galley.

The book itself is a largely unstructured collection of salty yarns about mutiny, exploration, slavers, pirates and high adventure – the chapter headings themselves tell a story, for they include: Chpt 1 Deep Sea Roving, Chpt IV The Profession of Piracy, Chpt VIII St Helena and the Slavers and Chpt XI Gambling with Death.

I can’t be sure that the proportions of the tippy-looking vessel shown are truly representative, but for me at least, this drawing of a galley from the chapter on the Profession of Piracy raises some practical points. It has a rig that would normally be expected to be best in beating rather than running – but I suspect sailing upwind was not its main purpose. For one thing I imagine the rowing galleries must have been vulnerable to digging-in when heeled, causing a kind of wild reverse-broach; for another I’d guess that like one of Pete Culler’s recreational skiff users, the commanders of these craft would row upwind when it was faster than sailing.

The power question is interesting. By my count there are two galleries of 27 oars here, each with six oarsmen. If well trained and well they fed, could theoretically deliver 0.2hp each – and by my calculation hat’s 324 oarsmen who, in my calculation should be able to deliver a total of 65hp. That’s not a huge amount of grunt for a ship this size, but even this figure would have to be reduced by some factor because it must have been difficult for the oarsmen at the inner and outer extremes of each oar to deliver their theoretical maximum, either because of the lack of travel or because of too much.

Surely, the man by the gunwale must have been chosen for his massive strength and the man at the far end for his height and span?

The detail shown here is fabulous. Just look at the warlike group on the forecastle and the three guns. I’d hate to see one of these coming my way, particularly if I had no wind to escape!

Here’s what Keble-Chatterton has to say:

‘The corsairs of Tunis rarely emerged from the Mediterranean, but sailed about off the south of Sardinia, or Cape Passaro at the heel of Sicily, or that historic pirate area among the Ionian Islands. The latter was a risky sphere, for the Venetian naval galleys with sails, masts, big crews of oarsmen, and with bow-guns, wsere not infrequently to be met with. The Moors feared these Venetians as their deadliest enemies, nor was the Battle of Lepanto yet forgotten. Using handy lateen-sail feluccas, with plenty of men to row as required in light or head winds, the Tunis pirates had and endless series of bays, creeks, and islands wherein to creep for rest and recreation. Such islands as Candia, Lampedusa, Rhodes and Cyprus could be used; but Tunis itself, being an open roadstead with inadequate protection from the fort, was not for them an ideal base. Algiers, on the contrary, was protected by a mole and a citadel; and there was a light showing to enable the rovers to get home from the sea.’

Don’t miss something good. Subscribe to intheboatshed.net’s weekly newsletter.

Free plans for the intheboatshed.net Ella skiff now online and available to download



[ad name=”intheboatshed-post”]

skiff-zip-drawing

12ft length overall by 4ft beam, by 400lbs displacement, designed for stitch and glue construction using 1/4in or 3/8in 4ft by 8ft plywood

If you build this boat PLEASE send me a report about how the project went and how it works on the water, together with photos! I’m at gmatkin@gmail.com, and will usually be available to  provide online advice.

At last I’ve managed to find a few hours to make up a plans package! I hope it was worth the wait. In a mass of material like this there will no doubt be an error or two, so if you find any, please let me know and I’ll put them right.

For previous posts on the development of this little boat, click here and here.

From the notes:

The Ella skiff as laid out in these plans is a lightweight general purpose stitch and glue flattie skiff for use in sheltered waters with no strong currents or tides. It is not suitable for use on the sea or in hazardous waters.

It is meant to be a simple and quick stitch and glue building job of a size that is convenient for building in domestic garages made to take a small to medium-sized car, which probably describes the building area available to most people.

Like this boat? Send your comments to me at gmatkin@gmail.com.

The boat is designed with rowing primarily in mind, though it could also be used with a VERY small outboard of NO MORE than 2hp. Too many accidents take place because outboards of the wrong size have been used, and far too many of these are fatal. If a small outboard is to be used, the transom should be doubled to ensure it can support the weight of the engine.

The name came from my daughter, who has taken rather a shine to the boat – readers of intheboatshed.net will find photos of a model she has made.

Compared with the Julie skiff, the form of a boat like this must be strongly influenced by the need to work in a decent amount of displacement into a shorter hull, as anyone who compares the lines drawings of the two boats will quickly see. The Ella skiff is therefore a more curvy boat than her big sister, but I hope that her more jaunty sheerline lends a certain cuteness people will like. The stem is angled somewhat in order to turn splashes and ripples downward, for I know that dryness is an important part of comfort in small craft, especially for those unused to boating.

Sailing enthusiasts will note that I have not drawn any details for a sailing version of this boat and I would prefer that no builder should add a sailing rig to this bare design. Boats like this should not be converted for sailing without serious thought about the safety and construction issues.

However, my daughter has asked me to develop a sailing version for her, and at some point I intend to do so. The design for this boat will feature a good amount of built-in bouyancy for safety, will be half-decked, and will probably have a balanced lug rig for ease of sailing.

This boat has been designed by an amateur with no qualifications in boat design or boatbuilding and should be regarded as experimental. The designer accepts no liability for any loss or accident that may result from following these instructions or plans or from any loss or accident that may follow from using this boat.

Click here to download the latest version of the free Ella skiff plans.

PS If you’re looking for a longer, sleeker but equally easy to build rowing skiff, click here.

PPS There’s now a 14ft version, the Sunny skiff. Click here.

This boat is designed to be built using the stitch and glue technique – if you haven’t done this before you might be interested in my book Ultrasimple Boat Building: 17 Plywood Boats Anyone Can Build or one of the other books on this topic available from Amazon.

Panels drawings and coordinates for the 12ft flat-bottomed Ella rowing skiff

[ad name=”intheboatshed-post”]

panels-plotting-1

Ella skiff, panel plotting, sheet 1

Tonight, I’ve finally managed to find some time to make a little more progress on the plans for the stitch and glue flat bottomed Ella rowing skiff. We now have four drawings to show where the panels that make up this stitch and glue-built boat fit on three 8 by 4ft sheets and one 4ft by 4ft sheet of ply; and we have four tables of coordinates to enable builders to markout and finally cut out their material, create the necessary taped or butt-strapped joints  before beginning assembly.

I won’t explain how stitch and glue works here as there’s a lot of material available on this both on the Internet and in books such as my Ultrasimple Boatbuilding – the only thing I’d say is please don’t try the process without reading about it properly first. That way lies sticky madness, strange-shaped boats and epoxy glop that won’t go off, as at least some people have found in the past. Just check the forums…

Here are the drawings files you’ll need: Ella skiff plans.

A few warnings are required here.

Prospective builders should be aware that I am not a qualified naval architect and that my plans are amateur and experimental. I accept no responsibility for any injury or loss arising from building or using this boat and I urge builders and users of this boat to do so with care.

This boat is not for use on the sea or in any hazardous conditions. It is a small boat suitable for rowing on small lakes and slow-flowing rivers. It may be rowed but should not be used with an outboard of any kind unless the stern is doubled and otherwise reinforced. Even if that were done, it would be dangerous to use an outboard of more than 1hp. This boat is not designed to hydroplane and should not be made to do so – far too many fatal accidents occur each year beause some bozo thought it was fun or safe to put a large engine on a boat for which it was not designed.

I would also ask builders that if any coordinate creates a line that does not appear as it does in the drawings to contact me immediately. You may have found an error, and will need corrected measurements to be able to go forward. Also, I will want to correct anything that is wrong for the sake of future builders. In general, if you build this boat, please contact me at gmatkin@gmail.com. Especially with the first few boats built, I will want to be in close touch in order to ensure the boats are successful and the plans cause no problems.

These plans aren’t entirely complete – for example, they don’t show where the oarlocks need to go, or specify the gunwales or inwales – and I haven’t written my usual short essay yet. All of that will come.

Finally, if after all this you are still interested in building this small, simple and perhaps elegant little boat, I would strongly suggest that you build a model first! Read all about making a model here and here. There is also more on the Ella skiff design including the preliminary drawings here.

PS – It’s become clear that depending on your build, some folks will find the thwart a little high – if that could be you, it will be a very simple job to make the seat lower if you do so at an early stage.

Complete plans will follow, so why not subscribe to intheboatshed.net?